Back to... Home!

Doll Shoes ©1999
Cloth Dolls by Stitch 'N Stuff

If you are like me and love to rescue dolls from church bazaars and garage sales, below is a doll shoe pattern that you will find easy to make and very versatile. The pattern fits most 18" vinyl dolls, but I have given directions to adjust the pattern to fit any doll you might have. You can also use this pattern for dolls you make yourself.

The only thing you need to know is the length of your doll’s foot, the size of the toe area (the widest part) and the size of the heel area (the narrowest part).  After printing, the sole pattern should measure 3 1/2 inches long, the toe area is 2 inches and the heel is 1 1/2 inches, including the seam allowance.

18" Doll Shoe Pattern

DIRECTIONS

To make the shoes to fit the 18" vinyl doll, you will need to cut out 4 upper pieces and 4 soles (2 of each piece are for lining and can be cut out of different material than the shoe if you wish).  I like to use denim, fleece, fake fur or other heavy material.  I also use satin, flannel, or other lighter weight materials, but I like to use iron-on interfacing on the back of each piece so the finished shoes are not flimsy.  There is no right or wrong, just decide how you want the finished shoe to look

Now you can embellish with a small silk flower, or a bow or button, etc. Or you can cut a length of ribbon long enough to go around the doll’s leg and attach the middle of the ribbon at the back of the shoe. Make it long enough for ballerina shoes if you wish. If you make the shoe out of fur, you will have a pair of furry slippers. For the sole, you can use the non-slip material sold for children’s pajama feet.

To alter the pattern to fit any doll

When altering the size of the pattern, be sure to cut off the seam allowance before increasing or decreasing the pattern because re-sizing will affect the seam allowance and you will not get as good a fit. You can easily add the seam allowance back after you have re-sized the pattern.

So if your doll’s foot is 2" long divided by 3" (the length of the sole pattern I have given you) you would get .666 or you would need to decrease the size of the sole pattern by 66%.

Note: Remember, if your doll’s foot is longer than 3", you would need to increase and your % would be great than 100%. If you doll’s foot is smaller than 3", you would have to decrease and your % would be less than 100%.

Sole pattern @ 66% of original

The new sole measures 2" long so now you have the correct length. Next, you need to determine the crosswise fit.

Cut out the new pattern and tape to a larger piece of paper. Measure the toe area and the heel area of your doll’s foot and compare to your new pattern. Add or subject the necessary width remembering to divide the difference by two and add or subtract an equal amount to each side of the foot. It may be necessary to add a little bit of extra room. The doll I used had toes that were spread apart slightly and the big toe was curled up. I decided to add an 1/8 " extra at the toes and I used fleece which has some stretch.    I decided that I needed 1 ¼" across the toes and ¾" at the heel. After you determine what you need, redraw the foot piece taking into account the new measurements and then add your seam allowance as illustrated below:

The red is the width that I added to the pattern and the blue is the seam allowance that I added back in.

Now take a piece of string and measure around the new sole pattern by taping the string on the sewing line as illustrated below (a). My sole pattern which I decreased--at 66%-- measures 5 ½" around the sole. With the extra width I added, my new sole pattern measures 6" around, so the difference I need to add to my upper shoe pattern in order for it to fit the sole is ½". Once again, remember to divide the difference in half and add an equal amount to each side of the shoe at the back seam as illustrated below in (b) (red equals the extra added and blue is the new seam allowance):

Now you can follow the directions as for the 18" vinyl doll shoe pattern.

Variation in upper shoe pattern

Below is a different upper shoe pattern for you to use. For this pattern you would need to sew a ribbon on either side as marked on the pattern and tie with a bow at the front of the shoe. Directions for the shoe would be the same except you would stitch the ribbon at the dots on the upper shoe pattern before putting the shoe together. I like to turn the ribbon under about 3/8" before I sew the lining to the shoe so that the ribbon can’t pull out. Make sure to have the ribbon between the shoe and lining with the ribbon toward the back as in the picture below. For the embellishment on the shoe I have pictured, I made a yo-yo. To make a yo-yo, cut out a 2" circle and hand-baste, turning the material to the wrong side in a narrow hem as you sew. Pull thread and flatten to make a circle and tack to the front of the shoe.

Upper shoe variation

Be sure to place your ribbon between the layers of material (right sides together) with the ribbon extending out the back of shoe as pictured below.

You may use this pattern to make dolls for your personal use or to sell at local craft shows and in limited quantities.  However, we do require that you credit Cloth Dolls by Stitch 'N Stuff for the design on your hangtag or in any advertising that you do.   You may not reproduce this pattern for sale or mass-produce dolls made from this pattern.

Home